分板機解決6毫米燈條不變形機器
Plate splitter solves the problem of 6 mm light bar without deformation
1.本機采用了獨特的多，甚至更多的切割方法，通過切割八片完成板，二上下為一組，以形成切削單元。他們是A，B，C，D四組。整個切割過程分為四個階段，一組葉片從A槽切斷所述電路板的30％，然后再切刀片B還在葉片運行時，再次完成切割的30％的量，然后再次選自B刀片罐已碾過，切割刀片?完成再次削減量的30％，最后由D組的最終切割刀片和擦拭器10％，由于少量的每次切割的，所以應力更傳統的剪裁方式，以減少80％以上，在切割過程中產生，董事會較好的分割邊緣光滑，董事會非常光滑，不扭曲不翹。目前僅切割鋁塑板后去保證了機器的不變形。
This machine adopts a unique multi or even more cutting method, through cutting eight pieces of complete plate, two up and down into a group, in order to form a cutting unit. They are group A, B, C, D. The whole cutting process is divided into four stages: a group of blades cut 30% of the circuit board from slot a, and then the re cutting blade B completes 30% of the cutting amount again while the blade is still running, and then it is selected again from the B blade tank which has been rolled, the cutting blade (c) completes 30% of the reduction again, and finally, the final cutting blade and wiper of group D are 10% The stress is more traditional cutting method to reduce more than 80%, which is produced in the cutting process. The edge of the board is better, the edge is smooth, and the board is very smooth without distortion and warping. At present, only after cutting the aluminum-plastic plate to ensure that the machine does not deform.
2，由于多個切削起見，非常光滑切割過程，大大提高了V-CUT槽的靶向能力，即使V-CUT很淺的槽板，它不會從導向槽V-CUT刀出現跳出的，避免不良。
For the sake of multiple cutting, the cutting process is very smooth, which greatly improves the targeting ability of V-CUT groove. Even if the V-CUT is very shallow, it will not jump out from the V-CUT cutter of the guide groove, so as to avoid bad performance.
3.由于小刀片的切割力，并采用瑞典進口高速鋼，切板鋁板刀片壽命可達一年，當片的耐用性大大增強。
As a result of the high-speed steel blade imported from Sweden, the blade life can be greatly enhanced when cutting.
4，全部采用激光干涉的激光測量?jī)x的校準，以確保刀后的第一刀可以繼續通過槽精確切割所述切割刀片的。提示跳動不大于0.02mm。確保完美的切割質量。
After the first cutter is cut accurately, the laser cutter can continue to cut through all the cutting slots of the laser cutter. It is suggested that the run out is not more than 0.02mm. Ensure perfect cutting quality.
